📌 Key Takeaways
- Topic: Toothpaste Grade Silica: Abrasive vs Thickening Silica, RDA Values and Specifications
- Keywords: silica polishing agent
- Published: 2026-11-20 12:07:07
- Field: Silica (SiO₂) raw materials · Inorganic non-metallic materials · Chemicals
Silica Flatting Agent: Gloss Reduction Mechanism, Grades and Applications
- Quartz Sand for Photovoltaic: High Purity Requirements for Solar Crucibles
- Wet granulation is the most frequently used technique to process MSNs, because of the many possibilities inherent in it [ 106 ]. Conventional wet granulation is well-suited for the granulation of silica nanocarriers, but several things should be considered during implementation. There are two possible sequences: first, the drug loading, followed by the granulation of the loaded carriers [ 104 ], or the opposite way, the granulation of the empty carriers, then loading the drug into the prepared granules. In the first case, during the planning and implementation of the process, special attention must be paid to the critical process parameters to steer clear of premature drug release [ 104 ]. In general, it can be noted that as little moisture as possible should be used during granulation, consequently decreasing the risk of premature drug release. Still, simultaneously, moisture adequate to produce the desired agglomeration must be made sure [ 104 ]. The risk of premature drug release depends to a certain extent on the chemical structure of the API and the carrier. Szewczyk and Prokopowicz developed doxycycline-loaded MSN pellets with prolonged release kinetics [ 40 ]. First, the drug was loaded into the pores, and then pellets were produced from the loaded mesoporous material with other excipients by wet extrusion and spheronization. For comparison, traditional doxycycline pellets were also prepared. This study demonstrated the importance of utilizing mesoporous carriers for the delayed or sustained release of water-soluble drugs. Pelletization was a successful method to reduce the initial burst release of doxycycline; twice the release time was observed compared to traditional pellets [ 40 ]. Szewczyk et al. developed another DDS loaded with an antibiotic compound (cefazolin) for the treatment of osteomyelitis [ 66 ]. The amine-functionalized MSN was successfully loaded with the drug, and because of the powerful interactions between the negatively charged cefazolin and the positively charged surface of the carrier, a prolonged release of 5 days was observed, which made sure a longer antibacterial influence than with classic pellets. This was proven by the microbiological activity assays of the pellets against S. aureus culture [ 66 ]. These results are promising in antibiotic or anticancer therapy, where therapeutic concentration is needed for a longer period [ 40, 66 ]. A comparable outcome was presented in another publication about metformin-containing MSN pellets with prolonged release kinetics [ 85 ]. After drug loading, pellets were formed with the mixture of the preloaded carriers and chitosan solution, and then the pellets were coated with five layers of chitosan. Since the stomach is not considered the best possible absorption surface for metformin, it is advisable to delay the release until conditions in the intestines are ideal for maximum bioavailability. Chitosan plays an important role in this formulation; it slows down and delays the metformin release and offers delayed and prolonged release kinetics, thereby preventing speedy blood level peaks after application [ 85 ]. On the contrary, Wang et al. published a post on MSN pellets filled with poorly water-soluble carbamazepine, and they observed better oral bioavailability compared to commercially available tablets based on in vivo analysis performed on dogs [ 86 ]. In vitro dissolution studies confirmed a raised dissolution rate compared to crystalline carbamazepine due to the amorphous state of the drug within the pores. This immediate-release pellet formulation allows for a reduction in the drug dose, sustaining the same clinical influence [ 86 ].
- Barium Sulfate vs Silica: Fillers for Coatings and Plastics Compared
- What Is Silica? Definition, Main Types, Key Properties and Industrial Uses (2026 Guide)
- Silica for Chromatography: Particle Size, Pore Size and Grade Selection
- 62. Wang H., Chen L., Li R., Lv C., Xu Y., Xiong Y. Polydopamine-coated mesoporous silica nanoparticles co-loaded with Ziyuglycoside I and Oseltamivir for synergistic treatment of viral pneumonia. Int. J. Pharm. 2023;645:123412. doi: 10.1016/j.ijpharm.2023.123412. [ DOI ] [ PubMed ] [ Google Scholar ]
CMP Slurry Silica: Colloidal vs Fumed Silica for Chemical Mechanical Polishing
What is silica (SiO₂)?
crystalline silica dust hazard
What is the difference between fumed silica and precipitated silica?
Denka spherical silica 44. Trzeciak K., Chotera-Ouda A., Bak-Sypien I.I., Potrzebowski M.J. Mesoporous silica particles as drug delivery systems - The state of the art in loading techniques and the recent progress in analytical approaches for monitoring these processes. Pharmaceutics. 2021;13:950. doi: 10.3390/pharmaceutics13070950. [ DOI ] [ PMC free post ] [ PubMed ] [ Google Scholar ]
What drives silica raw material prices?
silica for coatings Silica nanoparticles can be created and used in diverse shapes (sphere, cube, ellipsoid, rod). The shape of the particles can be characterized by the facet ratio, which is 1 for spherical particles, but can reach 4 in the case of elongated rod-shaped ones [ 1 ]. Particles with different aspect ratios may exhibit different biodistribution and elimination [ 10, 19, 25 ]. The residence time in the gastrointestinal system is influenced by the particle shape [ 1, 19 ]. Spherical nanoparticles have a shorter residence time than rod-shaped ones [ 19 ] and tend to accumulate in the liver. Simultaneously, in the case of rods, a more significant accumulation is observed in the spleen [ 10 ]. In addition, particles with a higher element ratio exert longer half-life in the bloodstream and show slower elimination [ 1, 19 ], possibly due to faster renal excretion of spherical than rod-shaped particles [ 19, 25 ]. By increasing the facet ratio, a longer degradation time can also be observed [ 25 ].
/news/article.htmlDisclaimer: Prices and data are for reference only and do not constitute purchasing or investment advice. Please credit the source when republishing.