Fused Silica CAS 60676-86-0: Identification, Properties and Safety Data

Published: Source: Silica Raw Materials News Section: Silica Raw Materials

📌 Key Takeaways

  • Topic: PPG Hi-Sil: Precipitated Silica Product Range and Applications
  • Keywords: crystalline silica dust hazard
  • Published: 2026-11-20 12:17:59
  • Field: Silica (SiO₂) raw materials · Inorganic non-metallic materials · Chemicals

Calcium Carbonate Filler vs Silica: Performance, Cost and Applications Compared

Silica Whiteness: How It Is Measured and Why It Matters for Coatings and Rubber
7. Vallet-Regi M., Rámila A., Del Real R.P., Pérez-Pariente J. A new property of MCM-41: Drug delivery system. Chem. Mater. 2001;13:308-311. doi: 10.1021/cm0011559. [ DOI ] [ Google Scholar ]
Silica for Rubber: Reinforcement Benefits, Grades and Compounding Tips
Another study concentrated on repaglinide, an oral antidiabetic drug [ 84 ] from the BCS class II, with poor solubility but high permeability. In addition, it has a significant first-pass effect, and the combination of these two features results in low oral bioavailability. The researchers prepared a repaglinide solid dispersion employing mesoporous silica to enhance solubility and drug release. Based on in vitro tests, the repaglinide-MSN complex exhibited significant improvement, compared to the pure drug [ 84 ]. Then this solid dispersion was effectively incorporated into a medicated chewing gum. This buccal administration causes the drug to bypass first-pass metabolism, further boosting oral bioavailability. Based on their clinical investigations, the researchers proved that this formulation showed an increased antidiabetic activity compared to the marketed product by measuring blood glucose levels. In summary, this solid dispersion chewing gum formulation can be a promising perspective in antidiabetic therapy [ 84 ].
Spherical Silica Manufacturer: Key Capabilities, Purity Control and Selection Criteria
43. Tu B., Jonnalagadda S. Amorphous stabilization of BCS II drugs using mesoporous silica. Int. J. Pharm. 2024;663:124555. doi: 10.1016/j.ijpharm.2024.124555. [ DOI ] [ PubMed ] [ Google Scholar ]
Is Silicon Dioxide Safe? What Science and Regulators Say
In spite of the advantages of solvent-free processes, solvent-based techniques offer a more widespread choice for filling the pores of the carriers. Each method listed here consists of two steps. First, mixing the drug solution and carrier, then removing the solvent [ 36 ]. The loading cycles can be repeated as many times as desired to increase the charging efficiency [ 20, 36 ]. These techniques can be effectively applied to molecules both with great and poor aqueous solubility [ 37 ]. However, removing the solvent residue at the end of the process is essential, owing to the toxicity of usually used organic solvents [ 56 ], and it is normally better to select a less toxic organic solvent, if possible [ 37, 56 ]. The adsorption of the API is also influenced by the properties of the solvent, such as viscosity or surface tension. This group includes the adsorption approach, the incipient wetness approach, the solvent evaporation method, and the use of liquid and supercritical CO 2. The adsorption technique (solvent immersion method) is a low-energy process, but the pores can be filled effectively only if the API reaches a high concentration in the solvent [ 37 ]. The carrier system is immersed in the concentrated drug solution, while the liquid fills the pores owing to capillary forces. The mesopores are then separated from the solution by filtration or centrifugation. Finally, the pores are dried under reduced pressure [ 2, 36, 37 ]. Drug loading abilities can be seen for some APIs by this loading approach, in the following figure ( Figure 1 ). During the incipient wetness impregnation, a greatly concentrated drug solution is added dropwise onto the surface of the mesopores, in a nearly equal volume to the pore volume of the carrier [ 37 ]. In this case, the pores are filled with liquid also owing to the capillary forces. Then the pores are dried out at a higher temperature and under reduced pressure [ 2, 36, 37 ]. Nevertheless, the third approach, solvent evaporation, is the most widely used because it can be applied to a wide range of molecules, regardless of their solubility, making it fitting for higher therapeutic doses as well. It is not necessary to prepare a concentrated solution since the concentration gradually increases during the process (owing to the evaporation of the solvent). During the process, the drug should be dissolved in a volatile organic solvent, which is mixed with the carrier system [ 20 ]. All solvents are then eliminated by quick evaporation [ 37 ], while the drug is absorbed into the pores of the drug carrier [ 36, 37 ]. The use of supercritical CO 2 brings about more productive and deeper pore filling compared to other solvents. In this state, neither a liquid phase nor a gas phase exists. It combines the brilliant diffusion capacity of gases and the excellent solvation capacity of liquids. In addition, it is non-toxic, non-flammable, and can be readily eliminated from the system. A cost-effective choice can be liquid CO 2, which is a similarly effective solvent [ 36, 37 ].

What Is a Silane Coupling Agent? How It Works and How to Choose One for Silica

What is silica (SiO₂)?

fumed silica supplier 42. Ortega E., Ruiz M.A., Peralta S., Russo G., Morales M.E. Improvement of mesoporous silica nanoparticles: A new approach in the administration of NSAIDS. J. Drug Deliv. Sci. Technol. 2020;58:101833. doi: 10.1016/j.jddst.2020.101833. [ DOI ] [ Google Scholar ]

What is the difference between fumed silica and precipitated silica?

silica production process Nanocarriers can be divided into two principal groups: organic and inorganic types. The organic group contains lipid nanocarriers, liposomes, polymeric nanoparticles, dendrimers, etc. In the case of the carriers in this group, the limited volume of delivered active pharmaceutical ingredient (API) is a clear disadvantage, along with decreased stability, and good sensitivity to temperature, pH, and enzymes in a physiological environment. The inorganic group contains metal oxide-, carbon-, silicon-, silica-, and quantum dot-based nanocarriers. Their benefits are greater stability and well-tunable physicochemical properties, but their accumulation in the body may be a key question of their applicability. Silica nanoparticles (SNP) are silicon dioxide (SiO 2 ) nanoparticles in an amorphous state and have excellent potential in the pharmaceutical industry and drug development due to their special properties. According to pore size, the most common, most well-liked, and most effective type of silica nanocarriers are the mesoporous silica nanoparticles (MSNs) [ 1 ].

What drives silica raw material prices?

silica

Cite this article: Silica Raw Materials News. "Aerosil Alternative: Equivalent Fumed Silica Grades and How to Switch ." Published 2026-11-20 12:17:59. /news/article.html
Disclaimer: Prices and data are for reference only and do not constitute purchasing or investment advice. Please credit the source when republishing.