TL;DR: Silica as an Excipient: Functions, Grades and Pharmaceutical Applications
. This post walks you through silica nanoparticles
, with practical tips on hydrophobic silica powder
and silica Alibaba
. Last updated 2026-11-20 07:18:59.
Key Takeaways
- What silica aerogel insulation is and why it matters
- Step-by-step tips for getting started with silica thixotropic agent
- Common silica 99% purity mistakes and how to avoid them
- Quick answers to frequent silica questions
In spite of the advantages of solvent-free processes, solvent-based techniques offer a more widespread choice for filling the pores of the carriers. Each method listed here consists of two steps. First, mixing the drug solution and carrier, then removing the solvent [ 36 ]. The loading cycles can be repeated as many times as desired to increase the charging efficiency [ 20, 36 ]. These techniques can be effectively applied to molecules both with great and poor aqueous solubility [ 37 ]. However, removing the solvent residue at the end of the process is essential, owing to the toxicity of usually used organic solvents [ 56 ], and it is normally better to select a less toxic organic solvent, if possible [ 37, 56 ]. The adsorption of the API is also influenced by the properties of the solvent, such as viscosity or surface tension. This group includes the adsorption approach, the incipient wetness approach, the solvent evaporation method, and the use of liquid and supercritical CO 2. The adsorption technique (solvent immersion method) is a low-energy process, but the pores can be filled effectively only if the API reaches a high concentration in the solvent [ 37 ]. The carrier system is immersed in the concentrated drug solution, while the liquid fills the pores owing to capillary forces. The mesopores are then separated from the solution by filtration or centrifugation. Finally, the pores are dried under reduced pressure [ 2, 36, 37 ]. Drug loading abilities can be seen for some APIs by this loading approach, in the following figure ( Figure 1 ). During the incipient wetness impregnation, a greatly concentrated drug solution is added dropwise onto the surface of the mesopores, in a nearly equal volume to the pore volume of the carrier [ 37 ]. In this case, the pores are filled with liquid also owing to the capillary forces. Then the pores are dried out at a higher temperature and under reduced pressure [ 2, 36, 37 ]. Nevertheless, the third approach, solvent evaporation, is the most widely used because it can be applied to a wide range of molecules, regardless of their solubility, making it fitting for higher therapeutic doses as well. It is not necessary to prepare a concentrated solution since the concentration gradually increases during the process (owing to the evaporation of the solvent). During the process, the drug should be dissolved in a volatile organic solvent, which is mixed with the carrier system [ 20 ]. All solvents are then eliminated by quick evaporation [ 37 ], while the drug is absorbed into the pores of the drug carrier [ 36, 37 ]. The use of supercritical CO 2 brings about more productive and deeper pore filling compared to other solvents. In this state, neither a liquid phase nor a gas phase exists. It combines the brilliant diffusion capacity of gases and the excellent solvation capacity of liquids. In addition, it is non-toxic, non-flammable, and can be readily eliminated from the system. A cost-effective choice can be liquid CO 2, which is a similarly effective solvent [ 36, 37 ].
Frequently Asked Questions
What is barium sulfate ?
silica aerogel blanket is the main topic of this post. "Silica Antiblocking Agent: How It Works, Particle Size Selection and Uses " explains what it is, why it matters and how to get started.
How do I get started with silica gel ?
Start with the step-by-step section of "Silicone vs Silica: What Is the Difference and Where Is Each Used? ", then explore our monocrystalline silicon and fumed silica 380 m2/g categories for more guides.
Is this Syloid silica guide up to date?
Yes. This post was last reviewed and updated on 2026-11-20 07:18:59.
"Matting Agent for Coatings: Types, Selection Guide and Performance Comparison " was written by the silica for battery separator Blog Team and last updated on 2026-11-20 07:18:59. If you quote or republish it, please link back to this page.
Comments
Have a question about hydrophobic fumed silica ? Leave a comment below.