What Is Synthetic Amorphous Silica (SAS)? Types, Safety and Regulatory Status

Published: Source: Silica Raw Materials News Section: Silica Raw Materials

📌 Key Takeaways

  • Topic: SiO₂ Explained: Chemical Formula, Structure, Properties and Applications of Silicon Dioxide
  • Keywords: alkaline silica sol
  • Published: 2026-11-20 04:49:10
  • Field: Silica (SiO₂) raw materials · Inorganic non-metallic materials · Chemicals
1. Introduction

Fumed Silica Brands Compared: Aerosil, Cab-O-Sil, HDK and Chinese Alternatives

Silica Antiblocking Agent: How It Works, Particle Size Selection and Uses
What Is Diatomaceous Earth? Composition, Grades and Common Uses
The size of the particles greatly affects the interaction with epithelial cells, cellular absorption, and therefore their effectiveness [ 1, 10, 12 ]. Furthermore, the size also influences the leakage of the API [ 12 ]. It has been proven in vitro that epithelial permeability can be increased by decreasing the size [ 1, 12, 13, 24 ]. Zhang et al. also observed that the cellular uptake of MSNs occurred in a time-, concentration-, and size-dependent manner based on in vitro studies performed on Caco-2 cell lines (20 nm, 60 nm, 90 nm) [ 24 ]. Nevertheless, more complex findings were gained in vivo. Wang et al. compared differently sized nanoparticles in various elements (100 nm, 250 nm, 480 nm) [ 12 ]. Similarly, Lamson et al. compared MSNs with different sizes to observe the influence of the particle size on bioavailability (20-1200 nm) [ 13 ]. Larger particles (normally around 500 nm) show slower release of the API and can form a strong interaction with the cell membrane [ 12 ], but cellular uptake is limited owing to their large size [ 1, 12 ]. Smaller particles (below 100 nm) show weaker interaction with the cell membrane but exert superb cellular uptake owing to their small size [ 12 ]. On the other hand, the smaller particles can slowly diffuse through the mucin layer covering the surface of the intestinal mucosa, become trapped in it, and aggregate, further worsening the absorption [ 1, 12, 13 ]. Furthermore, the decreasing particle size leads to increased release rate, owing to the larger specific surface area and faster degradation of the particles [ 1, 12 ], which can lead to early leakage of the molecules, worsening their absorption [ 1, 12 ]. As the diameter increases, the rate of degradation and drug release kinetics decreases, so larger particles have a longer half-life [ 12 ].
Spherical Silica Market 2026: Semiconductor Packaging Demand and Growth Outlook
Silica for Rubber: Reinforcement Benefits, Grades and Compounding Tips
65. Mal A., Prabhuraj R., Malhotra R., Valvi S.K., Ingle A., Srivastava R., De A., Bandyopadhyaya R. pH-responsive sustained delivery of doxorubicin employing aminated and PEGylated mesoporous silica nanoparticles leads to boosted antitumor efficacy in pre-clinical orthotopic breast cancer model. J. Drug Deliv. Sci. Technol. 2022;77:103800. doi: 10.1016/j.jddst.2022.103800. [ DOI ] [ Google Scholar ]

Silica 99% Purity: Specifications, Grades and Typical Applications

What is silica (SiO₂)?

silicon dioxide supplier

What is the difference between fumed silica and precipitated silica?

monodisperse silica spheres In spite of the advantages of solvent-free processes, solvent-based techniques offer a more widespread choice for filling the pores of the carriers. Each method listed here consists of two steps. First, mixing the drug solution and carrier, then removing the solvent [ 36 ]. The loading cycles can be repeated as many times as desired to increase the charging efficiency [ 20, 36 ]. These techniques can be effectively applied to molecules both with great and poor aqueous solubility [ 37 ]. However, removing the solvent residue at the end of the process is essential, owing to the toxicity of usually used organic solvents [ 56 ], and it is normally better to select a less toxic organic solvent, if possible [ 37, 56 ]. The adsorption of the API is also influenced by the properties of the solvent, such as viscosity or surface tension. This group includes the adsorption approach, the incipient wetness approach, the solvent evaporation method, and the use of liquid and supercritical CO 2. The adsorption technique (solvent immersion method) is a low-energy process, but the pores can be filled effectively only if the API reaches a high concentration in the solvent [ 37 ]. The carrier system is immersed in the concentrated drug solution, while the liquid fills the pores owing to capillary forces. The mesopores are then separated from the solution by filtration or centrifugation. Finally, the pores are dried under reduced pressure [ 2, 36, 37 ]. Drug loading abilities can be seen for some APIs by this loading approach, in the following figure ( Figure 1 ). During the incipient wetness impregnation, a greatly concentrated drug solution is added dropwise onto the surface of the mesopores, in a nearly equal volume to the pore volume of the carrier [ 37 ]. In this case, the pores are filled with liquid also owing to the capillary forces. Then the pores are dried out at a higher temperature and under reduced pressure [ 2, 36, 37 ]. Nevertheless, the third approach, solvent evaporation, is the most widely used because it can be applied to a wide range of molecules, regardless of their solubility, making it fitting for higher therapeutic doses as well. It is not necessary to prepare a concentrated solution since the concentration gradually increases during the process (owing to the evaporation of the solvent). During the process, the drug should be dissolved in a volatile organic solvent, which is mixed with the carrier system [ 20 ]. All solvents are then eliminated by quick evaporation [ 37 ], while the drug is absorbed into the pores of the drug carrier [ 36, 37 ]. The use of supercritical CO 2 brings about more productive and deeper pore filling compared to other solvents. In this state, neither a liquid phase nor a gas phase exists. It combines the brilliant diffusion capacity of gases and the excellent solvation capacity of liquids. In addition, it is non-toxic, non-flammable, and can be readily eliminated from the system. A cost-effective choice can be liquid CO 2, which is a similarly effective solvent [ 36, 37 ].

What drives silica raw material prices?

silica for 3D printing 74. Yuan F., Quan Ldong Cui L., Goldring S.R., Wang D. Growth of macromolecular prodrug for rheumatoid arthritis. Adv. Drug Deliv. Rev. 2012;64:1205-1219. doi: 10.1016/j.addr.2012.03.006. [ DOI ] [ PMC free article ] [ PubMed ] [ Google Scholar ]

Cite this article: Silica Raw Materials News. "Acidic Silica Sol: Properties, Stability and Applications ." Published 2026-11-20 04:49:10. /news/article.html
Disclaimer: Prices and data are for reference only and do not constitute purchasing or investment advice. Please credit the source when republishing.