📌 Key Takeaways
- Topic: Aerosil R972: Specifications, Hydrophobic Properties and Equivalent Grades
- Keywords: hollow glass microspheres
- Published: 2026-11-20 06:28:23
- Field: Silica (SiO₂) raw materials · Inorganic non-metallic materials · Chemicals
Quartz Sand Supplier: How to Choose by Purity, Grain Size and Logistics
- What Is Fused Silica Sand? Properties and Uses in Investment Casting and Refractories
- Glass Beads vs Silica Microspheres: Differences and Uses
- Silica Demand in 2026: Key Industries Driving Growth
- Wet granulation is the most frequently used technique to process MSNs, because of the many possibilities inherent in it [ 106 ]. Conventional wet granulation is well-suited for the granulation of silica nanocarriers, but several things should be considered during implementation. There are two possible sequences: first, the drug loading, followed by the granulation of the loaded carriers [ 104 ], or the opposite way, the granulation of the empty carriers, then loading the drug into the prepared granules. In the first case, during the planning and implementation of the process, special attention must be paid to the critical process parameters to steer clear of premature drug release [ 104 ]. In general, it can be noted that as little moisture as possible should be used during granulation, consequently decreasing the risk of premature drug release. Still, simultaneously, moisture adequate to produce the desired agglomeration must be made sure [ 104 ]. The risk of premature drug release depends to a certain extent on the chemical structure of the API and the carrier. Szewczyk and Prokopowicz developed doxycycline-loaded MSN pellets with prolonged release kinetics [ 40 ]. First, the drug was loaded into the pores, and then pellets were produced from the loaded mesoporous material with other excipients by wet extrusion and spheronization. For comparison, traditional doxycycline pellets were also prepared. This study demonstrated the importance of utilizing mesoporous carriers for the delayed or sustained release of water-soluble drugs. Pelletization was a successful method to reduce the initial burst release of doxycycline; twice the release time was observed compared to traditional pellets [ 40 ]. Szewczyk et al. developed another DDS loaded with an antibiotic compound (cefazolin) for the treatment of osteomyelitis [ 66 ]. The amine-functionalized MSN was successfully loaded with the drug, and because of the powerful interactions between the negatively charged cefazolin and the positively charged surface of the carrier, a prolonged release of 5 days was observed, which made sure a longer antibacterial influence than with classic pellets. This was proven by the microbiological activity assays of the pellets against S. aureus culture [ 66 ]. These results are promising in antibiotic or anticancer therapy, where therapeutic concentration is needed for a longer period [ 40, 66 ]. A comparable outcome was presented in another publication about metformin-containing MSN pellets with prolonged release kinetics [ 85 ]. After drug loading, pellets were formed with the mixture of the preloaded carriers and chitosan solution, and then the pellets were coated with five layers of chitosan. Since the stomach is not considered the best possible absorption surface for metformin, it is advisable to delay the release until conditions in the intestines are ideal for maximum bioavailability. Chitosan plays an important role in this formulation; it slows down and delays the metformin release and offers delayed and prolonged release kinetics, thereby preventing speedy blood level peaks after application [ 85 ]. On the contrary, Wang et al. published a post on MSN pellets filled with poorly water-soluble carbamazepine, and they observed better oral bioavailability compared to commercially available tablets based on in vivo analysis performed on dogs [ 86 ]. In vitro dissolution studies confirmed a raised dissolution rate compared to crystalline carbamazepine due to the amorphous state of the drug within the pores. This immediate-release pellet formulation allows for a reduction in the drug dose, sustaining the same clinical influence [ 86 ].
- Silica for Rheology Control: How to Select the Right Silica and Dosage
Solvay Zeosil: Highly Dispersible Silica Grades for Tires and Rubber
What is silica (SiO₂)?
silica for adhesives The drug loading capacity and the drug release profile for each drug loaded by the solvent immersion approach.
What is the difference between fumed silica and precipitated silica?
silica for toothpaste abrasive Lyophilization can be safely used for heat-sensitive drug substances because the drug is formulated at low temperatures and low pressure. Another advantage compared to direct compression is that the poor flowability does not cause problems here, and the pore structure of the nanoparticle is not damaged in the absence of compression. The freeze-drying process can be divided into three main steps: freezing, primary drying, and secondary drying [ 101 ]. The loaded carriers are homogenized with the prepared polymer solution [ 102, 103 ], containing matrix agents (PEG, polyvinyl alcohol (PVA), hydroxyethyl cellulose (HEC), polyvinylpyrrolidone (PVP), alginate, dextran), cryoprotectants (sucrose, or sugar alcohols such as mannitol, sorbitol), surfactants (polysorbates, sorbitan monooleate), super disintegrants (croscarmellose sodium) [ 102 ]. The resulting dispersion is filled into blisters and then lyophilized [ 102, 103 ]. During the process, the desired tablet shape is formed, adapting to the shape of the blister [ 102 ]. They are characterized by rapid disintegration (less than 30 s), low moisture content, and rapid dissolution [ 41, 102, 103 ]. Elmowafy et al. effectively optimized lyophilized tablet formulations using quercetin-loaded MSN carriers [ 41 ]. PVP-K30 was used as a polymeric stabilizer, PEG 6000 as a co-binding polymer, and sucrose as a cryoprotectant. This freeze-dried formulation permits fast disintegration and low friability (less than 1%). Importantly, the saturation solubility and the dissolution rate, and so the oral bioavailability of the poorly water-soluble quercetin boosted particularly, and it can be further improved by sublingual application [ 41 ]. Utilizing the right composition, an orally dispersible tablet can be produced, which is why its sublingual use is advantageous, because the API goes directly into the systemic circulation (bypassing the enteral circulation, so the first pass impact does not apply), hence improving oral bioavailability [ 41, 100 ]. Besides immediate drug release, sustained and even targeted drug release is also available, provided by appropriate formulation, thus increasing the therapeutic possibilities. These days, gastroretentive and mucoadhesive freeze-dried tablets are also available, further broadening the spectrum [ 102, 103 ].
What drives silica raw material prices?
silica for chromatography 7.1.1. Low-Dose Tablets
/news/article.htmlDisclaimer: Prices and data are for reference only and do not constitute purchasing or investment advice. Please credit the source when republishing.