📌 Key Takeaways
- Topic: CMP Slurry Silica: Colloidal vs Fumed Silica for Chemical Mechanical Polishing
- Keywords: barium sulfate
- Published: 2026-11-20 02:06:47
- Field: Silica (SiO₂) raw materials · Inorganic non-metallic materials · Chemicals
In spite of the advantages of solvent-free processes, solvent-based techniques offer a more widespread choice for filling the pores of the carriers. Each method listed here consists of two steps. First, mixing the drug solution and carrier, then removing the solvent [ 36 ]. The loading cycles can be repeated as many times as desired to increase the charging efficiency [ 20, 36 ]. These techniques can be effectively applied to molecules both with great and poor aqueous solubility [ 37 ]. However, removing the solvent residue at the end of the process is essential, owing to the toxicity of usually used organic solvents [ 56 ], and it is normally better to select a less toxic organic solvent, if possible [ 37, 56 ]. The adsorption of the API is also influenced by the properties of the solvent, such as viscosity or surface tension. This group includes the adsorption approach, the incipient wetness approach, the solvent evaporation method, and the use of liquid and supercritical CO 2. The adsorption technique (solvent immersion method) is a low-energy process, but the pores can be filled effectively only if the API reaches a high concentration in the solvent [ 37 ]. The carrier system is immersed in the concentrated drug solution, while the liquid fills the pores owing to capillary forces. The mesopores are then separated from the solution by filtration or centrifugation. Finally, the pores are dried under reduced pressure [ 2, 36, 37 ]. Drug loading abilities can be seen for some APIs by this loading approach, in the following figure ( Figure 1 ). During the incipient wetness impregnation, a greatly concentrated drug solution is added dropwise onto the surface of the mesopores, in a nearly equal volume to the pore volume of the carrier [ 37 ]. In this case, the pores are filled with liquid also owing to the capillary forces. Then the pores are dried out at a higher temperature and under reduced pressure [ 2, 36, 37 ]. Nevertheless, the third approach, solvent evaporation, is the most widely used because it can be applied to a wide range of molecules, regardless of their solubility, making it fitting for higher therapeutic doses as well. It is not necessary to prepare a concentrated solution since the concentration gradually increases during the process (owing to the evaporation of the solvent). During the process, the drug should be dissolved in a volatile organic solvent, which is mixed with the carrier system [ 20 ]. All solvents are then eliminated by quick evaporation [ 37 ], while the drug is absorbed into the pores of the drug carrier [ 36, 37 ]. The use of supercritical CO 2 brings about more productive and deeper pore filling compared to other solvents. In this state, neither a liquid phase nor a gas phase exists. It combines the brilliant diffusion capacity of gases and the excellent solvation capacity of liquids. In addition, it is non-toxic, non-flammable, and can be readily eliminated from the system. A cost-effective choice can be liquid CO 2, which is a similarly effective solvent [ 36, 37 ].
Silica Gel Desiccant: How It Works, Types, Capacity and How to Choose
- Silica Storage Conditions: How to Store Silica to Prevent Moisture and Caking
- 86. Wang Z., Chen B., Quan G., Li F., Wu Q., Dian L., Dong Y., Li G., Wu C. Increasing the oral bioavailability of poorly water-soluble carbamazepine utilizing immediate-release pellets supported on SBA-15 mesoporous silica. Int. J. Nanomed. 2012;7:5807-5818. doi: 10.2147/IJN.S37650. [ DOI ] [ PMC free post ] [ PubMed ] [ Google Scholar ]
- Toothpaste Grade Silica: Abrasive vs Thickening Silica, RDA Values and Specifications
- No new data were created or analyzed in this study. Data sharing is not applicable to this article.
- Is Silicon Dioxide Toxic? Safety of Amorphous vs Crystalline Forms Explained
- Being 100% chemical-free, you don't have to worry about it harming children or animals
- Hydrophobic Silica Powder: Properties, Water Repellency and Industrial Uses
Silica for Adhesives: Thickening, Thixotropy and Reinforcement Explained
What is silica (SiO₂)?
silica moisture absorber
What is the difference between fumed silica and precipitated silica?
silica for LED encapsulant Got 2025 Aug 17; Revised 2025 Sep 15; Accepted 2025 Sep 15; Collection date 2025 Sep.
What drives silica raw material prices?
silica supplier Germany
Cite this article: Silica Raw Materials News. "Silica OEM: How Private-Label and Custom Silica Manufacturing Works
." Published 2026-11-20 02:06:47.
Disclaimer: Prices and data are for reference only and do not constitute purchasing or investment advice. Please credit the source when republishing.
/news/article.htmlDisclaimer: Prices and data are for reference only and do not constitute purchasing or investment advice. Please credit the source when republishing.