Fused Silica Powder: Purity, Particle Sizes, CTE and Electronic Applications

Published: Source: Silica Raw Materials News Section: Silica Raw Materials

📌 Key Takeaways

  • Topic: Silica for Adhesives: Thickening, Thixotropy and Reinforcement Explained
  • Keywords: spherical vs angular silica
  • Published: 2026-11-20 05:04:47
  • Field: Silica (SiO₂) raw materials · Inorganic non-metallic materials · Chemicals
Mesoporous silica nanoparticles (MSNs) are a flexible platform for the improvement of water solubility and bioavailability of poorly water-soluble drugs through the stabilization of the API in the amorphous state. Two outstanding mechanisms facilitate such stabilization: physical entrapment within nanoscale pores with a diameter less than the size of the critical nucleus. In this case, the ordered molecular packing necessary to develop crystals cannot advance. Moreover, the unique interactions between the functional groups of APIs and the surface silanol groups of MSNs may immobilize drug molecules at or close to pore walls [ 44, 45 ]. Bavnhøj et al. used celecoxib to demonstrate that when loading is conducted under the pore-filling ability (PFC) of the silica matrix, the drug will be physically stable and amorphous for at least 18 months of dry storage. PFC-loaded along with near-PFC-loaded samples recrystallized, especially upon exposure to moisture, demonstrating the razor-thin margin between the level of loading and stability [ 46 ]. Although advantages are present, long-term stability is undermined by stress recrystallization. For example, α-mangostin began to recrystallize after 7-14 days at 25 °C and 95% relative humidity in MSNs with slightly broader pore size than the molecular size of the API, indicating that pore size must be finely tuned for productive confinement [ 47 ]. Similarly, simvastatin had the longest amorphous lifespan when loaded into pores of 4.5 nm. Still, it exhibited rapid recrystallization in materials with bigger pore size, underlining the critical importance of pore size for the preservation of amorphous stability [ 45, 47 ].

Silicon Dioxide Structure: Tetrahedral Network and Crystal Forms Explained

Spherical vs Angular Silica: Which Filler Performs Better and When?
Silica for Sealants: Grades, Functions and Formulation Guide
Silica for Silicone Rubber: Fumed vs Precipitated Silica and Grade Selection
71. Devangan P., Saini A., Patel D., Kolhe U. Solubility Enhancement of Aripiprazole via Mesoporous Silica: Preparation, Characterization, In vitro Drug Release, and Solubility Determination. J. Pharm. Innov. 2023;18:1316-1327. doi: 10.1007/s12247-023-09722-9. [ DOI ] [ Google Scholar ]
Wood Coating Matting Agent: How to Achieve a Low-Gloss, Clear Finish

Colloidal Silica Slurry: Specifications and Uses in CMP and Precision Polishing

What is silica (SiO₂)?

silicon dioxide manufacturer In spite of the advantages of solvent-free processes, solvent-based techniques offer a more widespread choice for filling the pores of the carriers. Each method listed here consists of two steps. First, mixing the drug solution and carrier, then removing the solvent [ 36 ]. The loading cycles can be repeated as many times as desired to increase the charging efficiency [ 20, 36 ]. These techniques can be effectively applied to molecules both with great and poor aqueous solubility [ 37 ]. However, removing the solvent residue at the end of the process is essential, owing to the toxicity of usually used organic solvents [ 56 ], and it is normally better to select a less toxic organic solvent, if possible [ 37, 56 ]. The adsorption of the API is also influenced by the properties of the solvent, such as viscosity or surface tension. This group includes the adsorption approach, the incipient wetness approach, the solvent evaporation method, and the use of liquid and supercritical CO 2. The adsorption technique (solvent immersion method) is a low-energy process, but the pores can be filled effectively only if the API reaches a high concentration in the solvent [ 37 ]. The carrier system is immersed in the concentrated drug solution, while the liquid fills the pores owing to capillary forces. The mesopores are then separated from the solution by filtration or centrifugation. Finally, the pores are dried under reduced pressure [ 2, 36, 37 ]. Drug loading abilities can be seen for some APIs by this loading approach, in the following figure ( Figure 1 ). During the incipient wetness impregnation, a greatly concentrated drug solution is added dropwise onto the surface of the mesopores, in a nearly equal volume to the pore volume of the carrier [ 37 ]. In this case, the pores are filled with liquid also owing to the capillary forces. Then the pores are dried out at a higher temperature and under reduced pressure [ 2, 36, 37 ]. Nevertheless, the third approach, solvent evaporation, is the most widely used because it can be applied to a wide range of molecules, regardless of their solubility, making it fitting for higher therapeutic doses as well. It is not necessary to prepare a concentrated solution since the concentration gradually increases during the process (owing to the evaporation of the solvent). During the process, the drug should be dissolved in a volatile organic solvent, which is mixed with the carrier system [ 20 ]. All solvents are then eliminated by quick evaporation [ 37 ], while the drug is absorbed into the pores of the drug carrier [ 36, 37 ]. The use of supercritical CO 2 brings about more productive and deeper pore filling compared to other solvents. In this state, neither a liquid phase nor a gas phase exists. It combines the brilliant diffusion capacity of gases and the excellent solvation capacity of liquids. In addition, it is non-toxic, non-flammable, and can be readily eliminated from the system. A cost-effective choice can be liquid CO 2, which is a similarly effective solvent [ 36, 37 ].

What is the difference between fumed silica and precipitated silica?

silica supplier Russia Pool Grade Diatomaceous Earth: Unlike food grade DE, pool grade diatomaceous earth is hazardous to eat or inhale. This is DE that has been treated at temperatures in excess of 1000°C or 1832°F to change its state to mostly crystalline silica. This increases its effectiveness as a pool filter but makes it dangerous for any other use. None of the info we provide on our site involves using pool grade DE.

What drives silica raw material prices?

silica gel The potential of MSNs may also be utilized well in the case of polypills. In this case, all drugs must be dissolved in the solvent. After that, the carriers must be loaded with this complex solution, employing one of the already mentioned drug loading techniques. This can be followed by tableting nanocarriers. This approach can be really beneficial in the treatment of hypertension, where combination therapy is most often used. Patient compliance could also be improved with the production of such a polypill, since taking one pill rather than multiple pills may be simpler for the combined treatment of high blood pressure [ 99 ].

Cite this article: Silica Raw Materials News. "Silica Microspheres: Sizes, Properties and Applications in Coatings, Cosmetics and Chromatography ." Published 2026-11-20 05:04:47. /news/article.html
Disclaimer: Prices and data are for reference only and do not constitute purchasing or investment advice. Please credit the source when republishing.