What Is Silica D50? How Median Particle Size Is Measured and Why It Matters

Published: Source: Silica Raw Materials News Section: Silica Raw Materials

📌 Key Takeaways

  • Topic: Syloid Silica: Matting, Excipient and Food Grades Explained, with Alternatives
  • Keywords: hollow silica
  • Published: 2026-11-20 05:47:09
  • Field: Silica (SiO₂) raw materials · Inorganic non-metallic materials · Chemicals

Silicon Oxide Anode (SiOx): How It Works and Its Advantages for Lithium-Ion Batteries

Silica as a Clarifying Agent: Uses in Beer, Wine and Beverages
Solvay Zeosil: Highly Dispersible Silica Grades for Tires and Rubber
In spite of the advantages of solvent-free processes, solvent-based techniques offer a more widespread choice for filling the pores of the carriers. Each method listed here consists of two steps. First, mixing the drug solution and carrier, then removing the solvent [ 36 ]. The loading cycles can be repeated as many times as desired to increase the charging efficiency [ 20, 36 ]. These techniques can be effectively applied to molecules both with great and poor aqueous solubility [ 37 ]. However, removing the solvent residue at the end of the process is essential, owing to the toxicity of usually used organic solvents [ 56 ], and it is normally better to select a less toxic organic solvent, if possible [ 37, 56 ]. The adsorption of the API is also influenced by the properties of the solvent, such as viscosity or surface tension. This group includes the adsorption approach, the incipient wetness approach, the solvent evaporation method, and the use of liquid and supercritical CO 2. The adsorption technique (solvent immersion method) is a low-energy process, but the pores can be filled effectively only if the API reaches a high concentration in the solvent [ 37 ]. The carrier system is immersed in the concentrated drug solution, while the liquid fills the pores owing to capillary forces. The mesopores are then separated from the solution by filtration or centrifugation. Finally, the pores are dried under reduced pressure [ 2, 36, 37 ]. Drug loading abilities can be seen for some APIs by this loading approach, in the following figure ( Figure 1 ). During the incipient wetness impregnation, a greatly concentrated drug solution is added dropwise onto the surface of the mesopores, in a nearly equal volume to the pore volume of the carrier [ 37 ]. In this case, the pores are filled with liquid also owing to the capillary forces. Then the pores are dried out at a higher temperature and under reduced pressure [ 2, 36, 37 ]. Nevertheless, the third approach, solvent evaporation, is the most widely used because it can be applied to a wide range of molecules, regardless of their solubility, making it fitting for higher therapeutic doses as well. It is not necessary to prepare a concentrated solution since the concentration gradually increases during the process (owing to the evaporation of the solvent). During the process, the drug should be dissolved in a volatile organic solvent, which is mixed with the carrier system [ 20 ]. All solvents are then eliminated by quick evaporation [ 37 ], while the drug is absorbed into the pores of the drug carrier [ 36, 37 ]. The use of supercritical CO 2 brings about more productive and deeper pore filling compared to other solvents. In this state, neither a liquid phase nor a gas phase exists. It combines the brilliant diffusion capacity of gases and the excellent solvation capacity of liquids. In addition, it is non-toxic, non-flammable, and can be readily eliminated from the system. A cost-effective choice can be liquid CO 2, which is a similarly effective solvent [ 36, 37 ].
Precipitated Silica Manufacturer: Production Process and Supplier Selection Guide
86. Wang Z., Chen B., Quan G., Li F., Wu Q., Dian L., Dong Y., Li G., Wu C. Increasing the oral bioavailability of poorly water-soluble carbamazepine utilizing immediate-release pellets supported on SBA-15 mesoporous silica. Int. J. Nanomed. 2012;7:5807-5818. doi: 10.2147/IJN.S37650. [ DOI ] [ PMC free post ] [ PubMed ] [ Google Scholar ]
Quartz Sand Supplier: How to Choose by Purity, Grain Size and Logistics

Quartz CAS 14808-60-7: Identification, Hazards and Regulatory Information

What is silica (SiO₂)?

acidic silica sol This equation fits especially well for premature release, up to 60% of the drug released, when there is no change in the matrix system during the release process. From a perspective of pore geometry, it basically controls drug release rates by affecting effective diffusion pathways. Boosted complexity of geometries raises tortuosity and reduces effective diffusion. High tortuosity and low pore connectivity cut down drug diffusion, consequently lowering the release rates. Furthermore, surface roughness and pore size distribution affect surface region, diffusion, and residence times, and thereby drug release kinetics. Thus, coupling the Fick diffusion model with parameters characterizing pore geometry (e.g., porosity, tortuosity, etc.) enables for more precise and automatic modeling of drug release kinetics. In this way, it is nicely clarified why release profiles differ for chemically comparable matrices due to differences in their geometrical shapes [ 59, 60 ].

What is the difference between fumed silica and precipitated silica?

silica filler for CCL 54. Richter M., Welzmiller S., Monsuur F., Völp A.R., Quadflieg J. Dry Amorphization of Itraconazole Using Mesoporous Silica and Twin-Screw Technology. Pharmaceutics. 2024;16:1368. doi: 10.3390/pharmaceutics16111368. [ DOI ] [ PMC free article ] [ PubMed ] [ Google Scholar ]

What drives silica raw material prices?

amorphous silica

Cite this article: Silica Raw Materials News. "Fumed Silica vs Precipitated Silica: Differences in Production, Properties and Uses ." Published 2026-11-20 05:47:09. /news/article.html
Disclaimer: Prices and data are for reference only and do not constitute purchasing or investment advice. Please credit the source when republishing.