Hollow Glass Microspheres vs Hollow Silica: Lightweight Fillers Compared

Published: Source: Silica Raw Materials News Section: Silica Raw Materials

📌 Key Takeaways

  • Topic: Silica Aerogel Insulation: Thermal Performance, Uses and Cost Comparison
  • Keywords: precipitated silica price
  • Published: 2026-11-20 03:20:54
  • Field: Silica (SiO₂) raw materials · Inorganic non-metallic materials · Chemicals

Silica for Underfill: Submicron Spherical Silica Requirements and Selection

What Is Silica Used For? 20+ Industrial and Consumer Applications Explained
In spite of the advantages of solvent-free processes, solvent-based techniques offer a more widespread choice for filling the pores of the carriers. Each method listed here consists of two steps. First, mixing the drug solution and carrier, then removing the solvent [ 36 ]. The loading cycles can be repeated as many times as desired to increase the charging efficiency [ 20, 36 ]. These techniques can be effectively applied to molecules both with great and poor aqueous solubility [ 37 ]. However, removing the solvent residue at the end of the process is essential, owing to the toxicity of usually used organic solvents [ 56 ], and it is normally better to select a less toxic organic solvent, if possible [ 37, 56 ]. The adsorption of the API is also influenced by the properties of the solvent, such as viscosity or surface tension. This group includes the adsorption approach, the incipient wetness approach, the solvent evaporation method, and the use of liquid and supercritical CO 2. The adsorption technique (solvent immersion method) is a low-energy process, but the pores can be filled effectively only if the API reaches a high concentration in the solvent [ 37 ]. The carrier system is immersed in the concentrated drug solution, while the liquid fills the pores owing to capillary forces. The mesopores are then separated from the solution by filtration or centrifugation. Finally, the pores are dried under reduced pressure [ 2, 36, 37 ]. Drug loading abilities can be seen for some APIs by this loading approach, in the following figure ( Figure 1 ). During the incipient wetness impregnation, a greatly concentrated drug solution is added dropwise onto the surface of the mesopores, in a nearly equal volume to the pore volume of the carrier [ 37 ]. In this case, the pores are filled with liquid also owing to the capillary forces. Then the pores are dried out at a higher temperature and under reduced pressure [ 2, 36, 37 ]. Nevertheless, the third approach, solvent evaporation, is the most widely used because it can be applied to a wide range of molecules, regardless of their solubility, making it fitting for higher therapeutic doses as well. It is not necessary to prepare a concentrated solution since the concentration gradually increases during the process (owing to the evaporation of the solvent). During the process, the drug should be dissolved in a volatile organic solvent, which is mixed with the carrier system [ 20 ]. All solvents are then eliminated by quick evaporation [ 37 ], while the drug is absorbed into the pores of the drug carrier [ 36, 37 ]. The use of supercritical CO 2 brings about more productive and deeper pore filling compared to other solvents. In this state, neither a liquid phase nor a gas phase exists. It combines the brilliant diffusion capacity of gases and the excellent solvation capacity of liquids. In addition, it is non-toxic, non-flammable, and can be readily eliminated from the system. A cost-effective choice can be liquid CO 2, which is a similarly effective solvent [ 36, 37 ].
What Is Silica Sol? Composition, Acidic vs Alkaline Types and Industrial Applications
Nevertheless, mesoporous carriers are frequently associated with poor tabletability because of bad powder flow behavior; thus, direct tableting can only be attained by adding diverse excipients in large quantities [ 95 ]. Such useful excipients include microcrystalline cellulose (filler), lactose monohydrate (filler), PVP (binder), sodium carboxymethylcellulose (disintegrant), croscarmellose sodium (super disintegrant), colloidal silica (anti-adhesion material), magnesium stearate (lubricant), and talc (lubricant) [ 39, 95, 96, 97 ]. However, the drug content in the dosage unit decreases with high amounts of excipients added, so larger tablets must be designed to attain the proper dose [ 95 ]. Another issue is that the greater compression force used during tableting may deform and damage the pore structure of the carrier, which might decrease the expected drug release rate [ 36, 97, 98 ]. When higher compression forces are applied, the pore diameter decreases, which affects both total pore volume and particular surface region, reducing the drug release rate from the carrier [ 97, 98 ]. The use of microcrystalline cellulose may be a solution to this problem, as it deforms plastically under pressure while distributing the energy accumulated in the tablet during compression. Furthermore, croscarmellose sodium may improve the drug release rate [ 97, 98 ]. Granulation of mesoporous material is a proper choice to solve issues related to poor powder rheology.
Quartz Sand for Photovoltaic: High Purity Requirements for Solar Crucibles
Utilizing DE as a Pesticide
Tosoh Silica: Product Range, Applications and Key Grades

What Is Hydrated Silica? Uses in Toothpaste, Cosmetics and Food Explained

What is silica (SiO₂)?

silica powder supplier

What is the difference between fumed silica and precipitated silica?

silica for chromatography

What drives silica raw material prices?

fused silica CAS 60676-86-0

Cite this article: Silica Raw Materials News. "Ultrafine Silica Powder: Particle Sizes, Specifications and Applications ." Published 2026-11-20 03:20:54. /news/article.html
Disclaimer: Prices and data are for reference only and do not constitute purchasing or investment advice. Please credit the source when republishing.