📌 Key Takeaways
- Topic: Silica Particle Size Guide: How D50, Mesh and Microns Affect Performance
- Keywords: silica for feed carrier
- Published: 2026-11-20 05:48:57
- Field: Silica (SiO₂) raw materials · Inorganic non-metallic materials · Chemicals
Thermal Conductive Filler: Silica vs Alumina vs Boron Nitride Compared
- Is There a Quartz Sand Shortage? Causes, Impact and Supply Outlook
- What Is Hollow Silica? Structure, Properties and Applications
- Fumed Silica 200 m²/g: Properties, Typical Uses and Comparable Grades
- 4.2. Solvent-Based Techniques
- Why Is Silicon Dioxide a Covalent Network Solid? Structure and Properties Explained
- Wet granulation is the most frequently used technique to process MSNs, because of the many possibilities inherent in it [ 106 ]. Conventional wet granulation is well-suited for the granulation of silica nanocarriers, but several things should be considered during implementation. There are two possible sequences: first, the drug loading, followed by the granulation of the loaded carriers [ 104 ], or the opposite way, the granulation of the empty carriers, then loading the drug into the prepared granules. In the first case, during the planning and implementation of the process, special attention must be paid to the critical process parameters to steer clear of premature drug release [ 104 ]. In general, it can be noted that as little moisture as possible should be used during granulation, consequently decreasing the risk of premature drug release. Still, simultaneously, moisture adequate to produce the desired agglomeration must be made sure [ 104 ]. The risk of premature drug release depends to a certain extent on the chemical structure of the API and the carrier. Szewczyk and Prokopowicz developed doxycycline-loaded MSN pellets with prolonged release kinetics [ 40 ]. First, the drug was loaded into the pores, and then pellets were produced from the loaded mesoporous material with other excipients by wet extrusion and spheronization. For comparison, traditional doxycycline pellets were also prepared. This study demonstrated the importance of utilizing mesoporous carriers for the delayed or sustained release of water-soluble drugs. Pelletization was a successful method to reduce the initial burst release of doxycycline; twice the release time was observed compared to traditional pellets [ 40 ]. Szewczyk et al. developed another DDS loaded with an antibiotic compound (cefazolin) for the treatment of osteomyelitis [ 66 ]. The amine-functionalized MSN was successfully loaded with the drug, and because of the powerful interactions between the negatively charged cefazolin and the positively charged surface of the carrier, a prolonged release of 5 days was observed, which made sure a longer antibacterial influence than with classic pellets. This was proven by the microbiological activity assays of the pellets against S. aureus culture [ 66 ]. These results are promising in antibiotic or anticancer therapy, where therapeutic concentration is needed for a longer period [ 40, 66 ]. A comparable outcome was presented in another publication about metformin-containing MSN pellets with prolonged release kinetics [ 85 ]. After drug loading, pellets were formed with the mixture of the preloaded carriers and chitosan solution, and then the pellets were coated with five layers of chitosan. Since the stomach is not considered the best possible absorption surface for metformin, it is advisable to delay the release until conditions in the intestines are ideal for maximum bioavailability. Chitosan plays an important role in this formulation; it slows down and delays the metformin release and offers delayed and prolonged release kinetics, thereby preventing speedy blood level peaks after application [ 85 ]. On the contrary, Wang et al. published a post on MSN pellets filled with poorly water-soluble carbamazepine, and they observed better oral bioavailability compared to commercially available tablets based on in vivo analysis performed on dogs [ 86 ]. In vitro dissolution studies confirmed a raised dissolution rate compared to crystalline carbamazepine due to the amorphous state of the drug within the pores. This immediate-release pellet formulation allows for a reduction in the drug dose, sustaining the same clinical influence [ 86 ].
How to Buy Silica Powder: Grade Selection, Supplier Checks and Ordering Tips
What is silica (SiO₂)?
how to modify nano silica It is necessary to grasp the drug release mechanisms in porous media. Three categories can be distinguished based on the driving forces that generate mass transport: advection, diffusion, and electrophoresis [ 3 ]. For nanocarriers, advection and diffusion are the most considerable types. In the case of advection, the liquid as a medium conducts the material transport. This fluid motion is ensured by mechanical forces (pressure, gravity, cohesive and adhesive forces) [ 3 ]. Additionally, three subcategories can be distinguished here: film flow, capillary flow, and permeation. In the case of film flow, the liquid spreads into a thin liquid layer in contact with the surface of the pores. This spreading produces the required flow pattern. Capillary flow is made sure by capillary action. The surface tension of the liquid and the combined impact of adhesive and cohesive forces contribute to its creation. The pressure difference across the meniscus in the capillary causes the movement of the liquid along the capillary. During permeation, the flow of the liquid through the pores was created with the help of an external driving force (pressure) rather than an internal one [ 3 ]. Another significant material flow category is diffusion [ 2, 57 ]. The driving force comes from the concentration difference, which is equalized by the Brownian motion of the particles [ 3 ].
What is the difference between fumed silica and precipitated silica?
E551
What drives silica raw material prices?
silica gel beads
/news/article.htmlDisclaimer: Prices and data are for reference only and do not constitute purchasing or investment advice. Please credit the source when republishing.