Silica for Thermal Insulation: Aerogel, Fumed Silica and Microporous Materials Compared

Published: Source: Silica Raw Materials News Section: Silica Raw Materials

📌 Key Takeaways

  • Topic: Spherical Silica Manufacturer: Key Capabilities, Purity Control and Selection Criteria
  • Keywords: silicon metal
  • Published: 2026-11-20 10:18:02
  • Field: Silica (SiO₂) raw materials · Inorganic non-metallic materials · Chemicals
In the case of solvent-free processes, the main advantage is that it is not necessary to get rid of the solvent residue from the system at the conclusion of the process, and the concentration of the API can also be controlled [ 36, 37 ]. Techniques employed in this class comprise physical mixing, co-milling, and melt sorption methods. The simplest approach is physical mixing [ 37 ], where fast drug filling is possible without special equipment. During direct mixing of the mesoporous carrier and the drug, the silanol groups on the surface of the silica bind the drug molecules. Nonetheless, its application is limited because it can be used largely for water-soluble molecules [ 37, 56 ]. Another method is co-milling, during which the mixture of the API and the nanocarrier is milled together [ 36, 37, 56 ]. In the case of the melt sorption method, the mixture of the API and the carrier system is heated above the melting point of the API under continuous stirring, while the melt is absorbed into the pores [ 36, 37 ]. After that, the system is cooled under lowered pressure, so that the molecules will be in an amorphous state in the pores [ 36, 37 ]. Nevertheless, this technique cannot be used in the case of heat-sensitive materials, due to the considerable thermal decomposition [ 20 ]. Microwave radiation can also be used for melting [ 2, 36 ].

Is There a Quartz Sand Shortage? Causes, Impact and Supply Outlook

How to Get a Free Silica Sample: What to Request and How to Test It
What Is Tetraethyl Orthosilicate? Properties, Uses and Role in Silica Synthesis
In spite of the advantages of solvent-free processes, solvent-based techniques offer a more widespread choice for filling the pores of the carriers. Each method listed here consists of two steps. First, mixing the drug solution and carrier, then removing the solvent [ 36 ]. The loading cycles can be repeated as many times as desired to increase the charging efficiency [ 20, 36 ]. These techniques can be effectively applied to molecules both with great and poor aqueous solubility [ 37 ]. However, removing the solvent residue at the end of the process is essential, owing to the toxicity of usually used organic solvents [ 56 ], and it is normally better to select a less toxic organic solvent, if possible [ 37, 56 ]. The adsorption of the API is also influenced by the properties of the solvent, such as viscosity or surface tension. This group includes the adsorption approach, the incipient wetness approach, the solvent evaporation method, and the use of liquid and supercritical CO 2. The adsorption technique (solvent immersion method) is a low-energy process, but the pores can be filled effectively only if the API reaches a high concentration in the solvent [ 37 ]. The carrier system is immersed in the concentrated drug solution, while the liquid fills the pores owing to capillary forces. The mesopores are then separated from the solution by filtration or centrifugation. Finally, the pores are dried under reduced pressure [ 2, 36, 37 ]. Drug loading abilities can be seen for some APIs by this loading approach, in the following figure ( Figure 1 ). During the incipient wetness impregnation, a greatly concentrated drug solution is added dropwise onto the surface of the mesopores, in a nearly equal volume to the pore volume of the carrier [ 37 ]. In this case, the pores are filled with liquid also owing to the capillary forces. Then the pores are dried out at a higher temperature and under reduced pressure [ 2, 36, 37 ]. Nevertheless, the third approach, solvent evaporation, is the most widely used because it can be applied to a wide range of molecules, regardless of their solubility, making it fitting for higher therapeutic doses as well. It is not necessary to prepare a concentrated solution since the concentration gradually increases during the process (owing to the evaporation of the solvent). During the process, the drug should be dissolved in a volatile organic solvent, which is mixed with the carrier system [ 20 ]. All solvents are then eliminated by quick evaporation [ 37 ], while the drug is absorbed into the pores of the drug carrier [ 36, 37 ]. The use of supercritical CO 2 brings about more productive and deeper pore filling compared to other solvents. In this state, neither a liquid phase nor a gas phase exists. It combines the brilliant diffusion capacity of gases and the excellent solvation capacity of liquids. In addition, it is non-toxic, non-flammable, and can be readily eliminated from the system. A cost-effective choice can be liquid CO 2, which is a similarly effective solvent [ 36, 37 ].
Quartz Powder for Ceramics: Functions, Grades and Particle Size Selection
7.2. Granules/Pellets
Silicon Metal vs Silica: Production Process and Key Differences

Silica Bulk Density: Typical Values by Type and Why It Matters for Handling

What is silica (SiO₂)?

colloidal silica supplier

What is the difference between fumed silica and precipitated silica?

silica industry outlook

What drives silica raw material prices?

how to disperse fumed silica 96. Sun W.J., Aburub A., Sun C.C. Particle Engineering for Enabling a Formulation Platform Suitable for Manufacturing Low-Dose Tablets by Direct Compression. J. Pharm. Sci. 2017;106:1772-1777. doi: 10.1016/j.xphs.2017.03.005. [ DOI ] [ PubMed ] [ Google Scholar ]

Cite this article: Silica Raw Materials News. "Silica Supplier South Africa: Producers, Grades and Sourcing Options ." Published 2026-11-20 10:18:02. /news/article.html
Disclaimer: Prices and data are for reference only and do not constitute purchasing or investment advice. Please credit the source when republishing.