📌 Key Takeaways
- Topic: Syloid Silica: Matting, Excipient and Food Grades Explained, with Alternatives
- Keywords: alkaline silica sol
- Published: 2026-11-20 02:14:03
- Field: Silica (SiO₂) raw materials · Inorganic non-metallic materials · Chemicals
What Is Hydrophobic Fumed Silica? Surface Treatment, Grades and Applications
- What Is Silica Used For? 20+ Industrial and Consumer Applications Explained
- Spherical Silica Market 2026: Semiconductor Packaging Demand and Growth Outlook
- 33. Zhang J., Dong Y., Liu X., Jin H., Wang S., An N., Wang L. Effective myocardial infarction treatment by targeted accumulation of Sulforaphane using porous magnetic silica nanoparticles. Int. J. Pharm. 2023;645:123389. doi: 10.1016/j.ijpharm.2023.123389. [ DOI ] [ PubMed ] [ Google Scholar ]
- Silica Supplier Brazil: Market Overview, Producers and Import Considerations
- Silica Microspheres: Sizes, Properties and Applications in Coatings, Cosmetics and Chromatography
- Wet granulation is the most frequently used technique to process MSNs, because of the many possibilities inherent in it [ 106 ]. Conventional wet granulation is well-suited for the granulation of silica nanocarriers, but several things should be considered during implementation. There are two possible sequences: first, the drug loading, followed by the granulation of the loaded carriers [ 104 ], or the opposite way, the granulation of the empty carriers, then loading the drug into the prepared granules. In the first case, during the planning and implementation of the process, special attention must be paid to the critical process parameters to steer clear of premature drug release [ 104 ]. In general, it can be noted that as little moisture as possible should be used during granulation, consequently decreasing the risk of premature drug release. Still, simultaneously, moisture adequate to produce the desired agglomeration must be made sure [ 104 ]. The risk of premature drug release depends to a certain extent on the chemical structure of the API and the carrier. Szewczyk and Prokopowicz developed doxycycline-loaded MSN pellets with prolonged release kinetics [ 40 ]. First, the drug was loaded into the pores, and then pellets were produced from the loaded mesoporous material with other excipients by wet extrusion and spheronization. For comparison, traditional doxycycline pellets were also prepared. This study demonstrated the importance of utilizing mesoporous carriers for the delayed or sustained release of water-soluble drugs. Pelletization was a successful method to reduce the initial burst release of doxycycline; twice the release time was observed compared to traditional pellets [ 40 ]. Szewczyk et al. developed another DDS loaded with an antibiotic compound (cefazolin) for the treatment of osteomyelitis [ 66 ]. The amine-functionalized MSN was successfully loaded with the drug, and because of the powerful interactions between the negatively charged cefazolin and the positively charged surface of the carrier, a prolonged release of 5 days was observed, which made sure a longer antibacterial influence than with classic pellets. This was proven by the microbiological activity assays of the pellets against S. aureus culture [ 66 ]. These results are promising in antibiotic or anticancer therapy, where therapeutic concentration is needed for a longer period [ 40, 66 ]. A comparable outcome was presented in another publication about metformin-containing MSN pellets with prolonged release kinetics [ 85 ]. After drug loading, pellets were formed with the mixture of the preloaded carriers and chitosan solution, and then the pellets were coated with five layers of chitosan. Since the stomach is not considered the best possible absorption surface for metformin, it is advisable to delay the release until conditions in the intestines are ideal for maximum bioavailability. Chitosan plays an important role in this formulation; it slows down and delays the metformin release and offers delayed and prolonged release kinetics, thereby preventing speedy blood level peaks after application [ 85 ]. On the contrary, Wang et al. published a post on MSN pellets filled with poorly water-soluble carbamazepine, and they observed better oral bioavailability compared to commercially available tablets based on in vivo analysis performed on dogs [ 86 ]. In vitro dissolution studies confirmed a raised dissolution rate compared to crystalline carbamazepine due to the amorphous state of the drug within the pores. This immediate-release pellet formulation allows for a reduction in the drug dose, sustaining the same clinical influence [ 86 ].
Silica in Cosmetics: Functions, Types and Safety
What is silica (SiO₂)?
spherical alumina The skin is our largest organ, which consists of three layers: the epidermis, dermis, and hypodermis. Owing to its big surface zone, it also serves as an essential gateway for drug administration [ 25 ], which is fitting for both local (dermal) or systemic (transdermal) therapy [ 25, 56 ]. In spite of the popularity of this administration route, it is a challenge to get the API into deeper layers of the skin. The outermost layer of the epidermis, the stratum corneum, is the biggest hurdle to molecular penetration [ 25, 56 ]. However, the molecules must be absorbed through the capillaries of the dermis to achieve a systemic impact, which can be facilitated employing nanocarriers [ 56 ]. In addition, sweat glands or hair follicles can be effective alternative routes for the molecules to enter the deeper layers of the skin [ 25, 56 ]. In summary, it can be called as the transappendageal route. Among physicochemical properties, particle size is one of the most vital factors influencing absorption. Particles in the range between 200 and 300 nm are suitable for local treatment of the skin in diseases such as atopic dermatitis [ 25 ] since particles larger than 75 nm do not pass through the stratum corneum [ 25 ]. Smaller particles (approximately 50 nm) are suitable for systemic treatment [ 25 ], and on the whole, it can be said that nanoparticles with a diameter smaller than 25 nm can penetrate the skin most effectively, so they can be used for transdermal drug administration with an appropriate formulation [ 56 ]. By controlling the size of the nanocarrier, they penetrate to different depths in the skin. From the element of surface characteristics, cationic amino-functionalized MSNs show more efficient penetration into deeper layers of the skin than the particles with anionic surfaces of the same size [ 25 ]. The use of MSNs as a drug carrier may improve aqueous solubility, stability, and skin penetration of the drug [ 61 ]. In a research, gels containing MSN were prepared by employing distilled water to form the base, adding the gelling agent (Poloxamer 407), and adding HPMC to enhance the viscosity [ 83 ]. In another publication, MSN containing oleogels were prepared with sunflower oil and the addition of colloidal silicon dioxide as a gelling agent [ 61 ]. According to in vitro experiments, the gel matrix also affected the drug release kinetics [ 61, 83 ]. Slower drug release was observed in the case of gels containing loaded MSNs, compared to the free carriers, and the outcomes demonstrated close to zero-order release kinetics [ 61 ]. According to in vitro biocompatibility studies, this gel complex did not show any evidence of cytotoxicity on dermal fibroblast cells. Moreover, according to in vivo dermal safety studies, it has been proven that this preparation does not cause skin irritation during application, and so this formulation can be considered a safe product [ 61 ].
What is the difference between fumed silica and precipitated silica?
ultrafine silica powder
What drives silica raw material prices?
silica storage conditions
/news/article.htmlDisclaimer: Prices and data are for reference only and do not constitute purchasing or investment advice. Please credit the source when republishing.